Holosun EPS Carry Red Dot: Factory Reset Instructions

Resetting your Holosun EPS Carry red dot sight back to factory settings can be a useful tool for troubleshooting issues or simply starting fresh. The process is fairly straightforward and only requires a few simple steps. Begin with locating the reset button on the back of the sight. This small lever is often unmarked but can be easily identified by its position.

For initiating a factory reset, you'll need to hold down the reset button for a period of time of approximately 5 seconds. You should see a flashing indicator on the sight indicating that the reset process is in progress.
After the completion is complete, the light will return to its normal state.
Your Holosun EPS Carry is now restored to its original settings. You can then proceed with configuring it according to your preferences.

Be sure to always refer to the user manual for specific instructions and details regarding your Holosun EPS Carry red dot sight.

Returning Your Holosun EPS Carry to Original Settings

Need to Tweak your Holosun EPS Carry Red Dot back to its Default configuration? It's Simple. Here's how:

First, ensure the Display is Activated. Then, locate the Button labeled "Mode".

Press and hold this Button for approximately 5 seconds.

You should See a series of Sequences on the Display. This indicates that the Red Dot is now Reset to its Default configuration.

Once complete, release the Switch. Your Holosun EPS Carry is now Operational with all settings at their Factory values.

Calibrating the Holosun EPS Carry Red Dot Sight

The Holosun EPS Carry Red dot sight is a popular choice for concealed carry applications due to its compact size and durable construction. However, like any optical device, it may require periodic re-zeroing. This can be easily accomplished by following these simple steps: First, find the adjustment screws on the side of the sight. These are typically located near the battery compartment. Using a small screwdriver, carefully turn the screws to fine-tune the point of impact. Initiate by making small adjustments and test fire the sight at various distances to ensure accuracy. Continue this process until you achieve a desired zeroing point.

Note that the adjustment screws can be easily damaged if overtightened, so use caution when turning them.
Guarantee that the battery is fresh and properly installed before making any adjustments.
If you encounter difficulty zeroing your sight, consult the manufacturer's guide for further assistance or contact Holosun customer support.

Restore Factory Settings for Holosun EPS Carry

To restore your Holosun EPS Carry to its factory settings, you will need to navigate through the sight's menu system. First, power up the optic by engaging the switch located at the side of the unit. Next, utilize the control buttons found on the holographic display to access the settings menu. Within the menu, locate the "Factory Reset" option and confirm it using the designated button. The EPS Carry will then undergo a reset sequence, which may take a few moments. Once complete, your sight will be restored to its default configuration.

Note: During the reset process, all user-configured settings will be erased.

Reset Your Holosun EPS Carry in a Flash

Need to get your Holosun EPS Carry back to factory settings? It's easier than you think! Here are the simple steps you need to follow:

First, turn off your sight. Then, find the tiny reset button on the side of the sight. Use a small tool like a paperclip or a pin to press and depress the reset button for about 5 seconds. You'll know it worked when the display starts flashing.

Wait

Your Holosun EPS Carry is now reset to factory default settings!

Reinitialize a Holosun EPS Carry Red Dot

Need to a freshstart/clean slate? Here's how you can to restore factory defaults your Holosun EPS Carry Red Dot.

First, confirm that the red dot is switched on. Next, website pinpoint the tiny button on the left/right side of the sight's housing/body. Maintain a continuous press on this button for at least 5 seconds/3 seconds. You should see a flashing light/blinking indicator indicating that the reset process has begun/started. Keep holding/pressing the button until the light stops blinking/flashing. Release the button and your Holosun EPS Carry Red Dot is now completely reinitialized.